Attenuation Calculator

Attenuation Calculator

Attenuation tells you how much of the sugar in your wort the yeast turned into alcohol. Enter your original and final gravity to get apparent attenuation, real attenuation, and ABV.

How attenuation is calculated

Attenuation measures the share of sugar the yeast ate during fermentation. There are two kinds. Apparent attenuation uses your raw gravity readings and is the number most brewers quote. Real attenuation corrects for the fact that alcohol is lighter than water, so it gives the true percentage of sugar consumed. Real attenuation is always a few points lower than apparent.

Apparent attenuation = (OG − FG) ÷ (OG − 1) × 100

So a beer that starts at 1.055 and finishes at 1.012 has an apparent attenuation of (0.055 − 0.012) ÷ 0.055, which is about 78 percent. Real attenuation uses the gravities converted to degrees Plato and the real extract of the finished beer, which this tool works out for you. It also reports ABV from the same two readings.

What attenuation tells you about your beer

Attenuation is really a measure of dryness. A highly attenuated beer has had most of its sugar turned into alcohol, so it tastes crisp and dry and finishes light. A beer with low attenuation keeps more unfermented sugar, so it tastes fuller, sweeter, and rounder. Neither is better; they suit different styles. A dry Belgian ale or a crisp lager wants high attenuation, while a sweet stout or a malty Scotch ale wants less.

Because attenuation controls how much sugar is left behind, it also drives the calorie and carbohydrate content of the finished beer. A drier, more attenuated beer carries fewer residual carbs, which is why light beers are brewed to attenuate as fully as possible. You can see that link directly with the beer calories calculator, where a lower final gravity pulls the carbohydrate calories down.

Attenuation and ABV move together but are not the same. ABV depends on the size of the gravity drop, while attenuation depends on the drop relative to the starting sugar. A big beer and a small beer can share the same attenuation yet have very different strengths.

Typical attenuation by yeast and style

Most of a beer’s attenuation is decided by the yeast strain and the mash. The table shows the range you can expect from common yeast types. Breweries publish an attenuation range for each strain, so you can predict your final gravity before you brew.

Yeast typeTypical apparent attenuationResult
English ale67–72%Malty, fuller body
American ale73–80%Clean, balanced
German lager75–82%Crisp, dry
Belgian ale80–88%Dry, light body
Saison85–95%Very dry

If your beer finishes far outside the strain’s published range, something is off. Attenuation well below the range usually means a stuck fermentation, under-pitched yeast, or a mash run too hot. Attenuation above the range can mean a wild yeast or a very fermentable wort. Comparing your result to the expected range is one of the fastest ways to spot a fermentation problem.

How to raise or lower attenuation

You have real control over how far your beer ferments. To raise attenuation and make a drier beer, mash at a lower temperature, around 148 to 150 degrees Fahrenheit, which creates more fermentable sugar. Pick a yeast strain with a high attenuation range, pitch enough healthy yeast, and keep the fermentation warm enough for the yeast to finish. A small addition of simple sugar also ferments fully and lifts attenuation.

To lower attenuation and keep more body, do the opposite. Mash hotter, around 156 to 158 degrees Fahrenheit, to leave more unfermentable sugar. Choose a lower-attenuating yeast and add body-building grains like crystal malt or oats. These leftover sugars survive fermentation, so the beer finishes sweeter and fuller.

When you plan a recipe, use the Brix to SG converter and the potential alcohol calculator together to set a target, then check your actual attenuation against that target once the beer is done.

Apparent versus real attenuation, explained simply

This is the point that confuses most new brewers, so it is worth slowing down. Your hydrometer measures density. Alcohol is less dense than water, so a fermented beer reads lighter than its true sugar content would suggest. That makes the apparent attenuation look higher than the amount of sugar actually consumed. Real attenuation strips the alcohol effect out and reports the true figure, which is why it is always a few points lower.

For a beer at 1.055 that finishes at 1.012, apparent attenuation is about 78 percent, while real attenuation is closer to 64 percent. Both numbers are correct; they just answer slightly different questions. Apparent attenuation is the everyday number brewers use to compare batches and judge dryness. Real attenuation is the scientific figure used in calorie and extract math. This calculator gives you both so you never have to guess which one a recipe or yeast sheet is quoting.

If you measure your final gravity with a refractometer rather than a hydrometer, remember to correct it for alcohol first with the refractometer correction calculator, or your attenuation number will be wrong.

A worked example from start to finish

Imagine an American pale ale. You mash at 150 degrees, pitch a clean American ale yeast, and measure an original gravity of 1.055. Two weeks later the beer reads 1.012. Enter those numbers and you get about 78 percent apparent attenuation, roughly 64 percent real attenuation, and about 5.6 percent ABV. The American ale yeast’s published range is 73 to 80 percent, so 78 percent sits right where it should. That single check tells you the fermentation was healthy and complete before you ever taste the beer.

Now suppose the same beer had stopped at 1.020 instead. Attenuation would be only about 64 percent apparent, well below the yeast’s range, a clear sign of a stuck fermentation. Knowing that, you could rouse the yeast, raise the temperature, or pitch fresh yeast to finish the job rather than bottling a sweet, under-attenuated beer by mistake. That is the real value of tracking attenuation: it turns a vague worry into a clear, numbers-based decision.

For more background, the American Homebrewers Association explains attenuation and yeast health in depth.

What else shapes your attenuation

Yeast and mash temperature get most of the attention, but several quieter factors also decide where your beer finishes. The grain bill matters: specialty malts like crystal and caramel malts hold sugars the yeast cannot ferment, so a recipe heavy in them will attenuate less and finish sweeter. Simple sugars such as table sugar, dextrose, or honey do the opposite, because they ferment almost completely and push attenuation up. Adjuncts like oats and wheat add body and lower apparent attenuation slightly.

Yeast health is just as important as yeast choice. A big enough pitch of fresh, well-aerated yeast ferments strongly and reaches the strain’s full attenuation range. An old or under-sized pitch tires early and leaves sugar behind, which shows up as low attenuation and a sweet, under-finished beer. Giving the yeast enough oxygen at the start and holding a steady, warm-enough temperature through the whole fermentation are the simplest ways to hit your target every time.

Troubleshooting a stuck fermentation

When your attenuation lands well below the yeast’s range, the beer is usually stuck rather than finished. First, confirm the reading is real by checking gravity on two days in a row; a steady number means fermentation has stopped. If it has stalled short, gently raise the temperature a few degrees, swirl the fermenter to rouse the yeast back into suspension, and give it a few more days. If that fails, pitching a fresh, highly attenuative yeast will often restart the process and carry the beer to its proper finish.

Once your beer reaches the attenuation you expected, you can trust the rest of your numbers. The ABV, the residual sweetness, and the calorie content all follow from that final gravity, so a healthy, complete fermentation is the foundation every other reading rests on.

Frequently Asked Questions

What is a good attenuation for beer?

Most beers land between 70 and 85 percent apparent attenuation. The right number depends on the style and yeast, so compare your result to your yeast strain’s published range.

What is the difference between apparent and real attenuation?

Apparent attenuation uses raw gravity readings and reads high because alcohol is light. Real attenuation corrects for that and shows the true share of sugar fermented, a few points lower.

Why did my beer attenuate too little?

Low attenuation usually means a stuck fermentation from under-pitched or unhealthy yeast, a mash run too hot, or a fermentation that got too cold. Rousing the yeast often helps.

Does higher attenuation mean more alcohol?

It often does, because more sugar is converted, but ABV depends on the size of the gravity drop. A big beer and a small beer can attenuate the same yet differ in strength.

How do I make a drier beer?

Mash cooler near 149 degrees, use a high-attenuating yeast, pitch enough healthy cells, and keep fermentation warm enough to finish.

Scroll to Top