Brewhouse Efficiency Calculator

Brewhouse efficiency = (measured gravity points × volume in US gallons) ÷ (grain in pounds × grain potential in points per pound per gallon). 5 kg of 37 PPG malt giving 20 litres at 1.050 is about 65%.

By John Walker · Published November 2026

Brewhouse Efficiency Calculator

Most base malts are 36–38 points per pound per gallon.

Brewhouse efficiency

64.8%
Typical for new all-grain setups

Points collected

264
Gravity points × gallons

Maximum possible

408
Grain lb × PPG

How it is calculated

Points collected = (OG − 1) × 1000 × volume (US gal)

Maximum points = grain (lb) × potential (PPG)

Efficiency = points collected ÷ maximum points × 100

Worked example

Inputs — Total grain (kg): 5; Average grain potential (PPG): 37; Volume into fermenter (litres): 20; Measured original gravity: 1.05.

Results — Brewhouse efficiency: 64.8%; Points collected: 264; Maximum possible: 408.

Brewhouse efficiency: how much sugar you actually extract

When you brew all-grain beer, the malt contains a fixed amount of potential sugar, but you never get all of it into the fermenter. Brewhouse efficiency is the percentage of that theoretical maximum you actually capture, measured from the gravity and volume of wort that reaches your fermenter. It is the number that explains why two brewers can follow the same recipe and land at different strengths, and it is the figure you must know to scale a recipe accurately. Most home all-grain systems run between 65% and 80%; commercial breweries, with finer control and better equipment, push higher.

The calculation compares what you got with what was possible. Points collected = (OG − 1) × 1000 × volume in US gallons. Maximum points = grain weight in pounds × the grain’s potential in points per pound per gallon (PPG). Divide the first by the second and you have your efficiency. For example, 5 kg of 37 PPG malt that yields 20 litres at 1.050 is running about 65% — a normal figure for a new all-grain set-up. The calculator above does this for you; the sections below explain how to read the result and raise it.

Mash efficiency versus brewhouse efficiency

These two terms are often confused, and the difference matters. Mash efficiency (sometimes called conversion or lauter efficiency) measures the sugar in the kettle before the boil — how well the mash and sparge did their job. Brewhouse efficiency measures the sugar that makes it all the way into the fermenter, so it also absorbs every loss after the mash: wort left behind in the kettle as trub, absorbed by the hops, clinging to the mash tun, or lost in transfer. Brewhouse efficiency is always the lower of the two, and it is the one to use when you design a recipe, because it reflects your whole process on your actual equipment. Enter the volume and gravity measured at the same point — in the fermenter — for a true figure.

Brewhouse efficiencyWhat it usually means
Below 60%Coarse crush, under-sparging, or large equipment losses
65–70%Typical for new or batch-sparge all-grain systems
70–78%A dialled-in home system
80%+Fine crush, fly sparge, minimal dead space; approaching commercial

Why consistency beats a high number

Chasing a high efficiency figure is less important than hitting the same figure every time. A brewer who reliably gets 68% can design recipes that land on target batch after batch; a brewer who swings between 60% and 78% will miss their gravity — and therefore their strength and colour — unpredictably. Once you know your system’s steady efficiency, you plug it into recipe software (or work backward by hand) to decide how much grain a target gravity needs. The Beer ABV Calculator then turns your measured original and final gravity into the actual ABV, and the OG to Plato Converter helps if your software or notes use Plato.

Sources & further reading: John Palmer, How to Brew; American Homebrewers Association

How to raise your brewhouse efficiency

If your efficiency is lower than you would like, a handful of changes account for most of the gains, and they are worth tackling in order of impact:

  • Crush finer. The single biggest lever. A coarse crush leaves sugar locked inside the grain; tightening the mill gap (or asking your supplier for a finer crush) exposes more starch to conversion. Go too far and you risk a stuck sparge, so finer-but-not-floury is the aim — a mash with rice hulls lets you crush finer safely.
  • Mash at the right pH and temperature. A mash pH around 5.2–5.4 and a full conversion rest give the enzymes the conditions they need. An iodine test confirms the starch has fully converted before you lauter.
  • Sparge thoroughly. Rinsing the grain bed with enough water at the right temperature washes out sugar that would otherwise stay behind. Fly (continuous) sparging extracts more than batch sparging, though batch sparging is simpler and more consistent.
  • Reduce dead space and losses. Wort left in the mash tun, kettle or lines never reaches the fermenter. Knowing and minimising these volumes raises brewhouse efficiency even if your mash efficiency is unchanged.

Water and grain bill interact with efficiency

Efficiency is not uniform across every beer. Very big beers — barleywines, imperial stouts — almost always show lower efficiency, because a huge grain bed is harder to rinse and holds back proportionally more sugar. If you design a strong beer at your normal efficiency, expect to fall a little short and plan extra grain accordingly. Your strike and sparge water volumes feed directly into this, and our Strike Water Calculator helps you hit the right mash temperature and ratio, which supports clean conversion. The grain bill also sets the beer’s colour, so when you adjust quantities to fix efficiency, re-check the shade with the SRM Beer Color Calculator.

Measuring efficiency correctly

An efficiency number is only as good as the two readings behind it: gravity and volume. Measure the volume in the fermenter accurately — a mis-estimated volume throws the whole calculation off — and take a gravity reading that has been corrected for temperature, since a hot sample reads low and would understate your efficiency. Use the Hydrometer Temperature Correction tool for that step. Record the result for every batch; over a few brews a clear, repeatable number emerges, and that number is what makes your recipes predictable.

Using efficiency to scale and troubleshoot

Once you know your efficiency, it becomes a diagnostic. If a batch comes in well below your usual figure, the cause is almost always one of the levers above — a coarser crush than normal, a rushed sparge, or a bigger grain bill than your system handles well. If it comes in high, you may have crushed finer or sparged more patiently than usual. Tracking brewhouse efficiency alongside your gravities turns every brew day into useful data, and it is the foundation of hitting your target ABV, colour and balance on purpose rather than by luck.

Brewhouse efficiency: quick answers

What efficiency should I expect?

Most home all-grain systems land between 65% and 80% brewhouse efficiency. A new or batch-sparge set-up often starts around 65–70%; a dialled-in system with a fine crush and careful sparging reaches the high 70s. The exact number matters less than its consistency: a steady 68% you can design around beats a figure that swings batch to batch.

Mash efficiency or brewhouse efficiency — which do I use?

Use brewhouse efficiency for recipe design, because it reflects the sugar that actually reaches your fermenter after every loss — kettle trub, hop absorption, dead space and transfer. Mash efficiency measures the kettle before the boil and is always the higher figure. Entering the volume and gravity measured at the same point in your process, in the fermenter, gives the true brewhouse number.

How do I improve a low result?

Crush finer first — it is the biggest lever — then check your mash pH and temperature, sparge more thoroughly, and reduce the wort left behind as dead space. Very large grain bills, as in barleywines and imperial stouts, naturally show lower efficiency, so plan extra grain for strong beers. Your water volumes feed into this; the Strike Water Calculator helps you mash at the right ratio and temperature for clean conversion.

Frequently asked questions

What is a normal brewhouse efficiency?

Home all-grain systems commonly land between 65% and 80%.

How is this different from mash efficiency?

Mash efficiency uses the volume and gravity in the kettle before the boil. Brewhouse efficiency uses what reaches the fermenter, so it includes boil, trub and transfer losses.

How can I improve efficiency?

A finer crush, correct mash pH, a thorough sparge and fewer losses to dead space all help.

Which volume should I enter?

The volume in the fermenter at the same time you took the gravity reading.

Note: Results are estimates for planning. Check measurements yourself, and never use any calculator to decide whether it is safe to drive.

Scroll to Top