Hard Seltzer ABV: How Strong Is It and How Much Sugar Makes It?

Most hard seltzer is 4% to 6% ABV, with 5% the most common. To brew a 5% hard seltzer at home, you need about 85 grams of sugar per litre, which is 11 ounces per US gallon or 3.5 pounds for a 5 gallon batch.

Hard seltzer is carbonated water with alcohol and a light flavour. ABV means alcohol by volume, the percentage of the drink that is pure alcohol. The alcohol in a true hard seltzer comes from fermenting plain sugar and water, which gives a clean, almost tasteless base. This guide covers how strong seltzers are, how to hit an exact ABV with sugar, and the easy shortcut that uses vodka.

Target ABVSugar per litreSugar per US gallonSugar for 5 gallonsStarting gravity
4%68 g9 oz (257 g)2.8 lb (1.3 kg)1.026
5%85 g11 oz (322 g)3.5 lb (1.6 kg)1.033
6%102 g14 oz (386 g)4.3 lb (1.9 kg)1.039
7%119 g16 oz (450 g)5.0 lb (2.3 kg)1.046
8%136 g18 oz (515 g)5.7 lb (2.6 kg)1.052

The table is for plain white table sugar and assumes the seltzer ferments completely dry.

How strong are store-bought hard seltzers?

Hard seltzer sits in the same range as beer. A standard can is 12 ounces at about 5%, which is one US standard drink.

TypeTypical ABVCalories per 12 oz
Light or session seltzer4% to 4.5%80 to 90
Standard hard seltzer5%100
Stronger “surge” style8%160 to 220
Spirit-based canned seltzer4.5% to 7%100 to 150

Not every can called a seltzer is made the same way. Some are brewed from sugar, some from malt, and some are vodka or tequila mixed with sparkling water. The label and the ABV tell you which you have. For a wider comparison of drinks, see our chart of calories in alcohol.

How do you work out the sugar for a target ABV?

Yeast turns sugar into alcohol at a steady rate. A simple rule that works well for sugar and water is:

Sugar (grams) = target ABV × 17 × litres

For 19 litres (5 US gallons) at 5%, that is 5 × 17 × 19 = 1,615 grams, or about 3.5 pounds.

To check your result, take a hydrometer reading before and after and use the standard formula:

ABV = (starting gravity − final gravity) × 131.25

Sugar and water ferment much drier than beer. There is nothing left behind to hold the gravity up, and the alcohol is lighter than water, so the final reading usually lands below 1.000, between 0.994 and 0.998. A seltzer that starts at 1.033 and ends at 0.995 is (1.033 − 0.995) × 131.25 = 5.0%. The ABV calculator does the sum, and the potential alcohol calculator predicts the strength before you start.

Which sugar should you use?

SugarAmount compared with table sugarNotes
White table sugar (sucrose)Same as the chartCheapest and very clean
Corn sugar (dextrose)About 15% moreThe usual brewing choice, ferments easily
Brown sugar or raw sugarSameLeaves colour and a molasses taste
Honey or agaveAbout 25% moreAdds flavour, no longer a neutral seltzer

For a clear, neutral seltzer, use white sugar or corn sugar. Anything with colour or flavour will show in the glass.

Why does hard seltzer need yeast nutrient?

This is the step that decides whether a batch works. Beer wort and grape juice are full of the nitrogen, vitamins and minerals that yeast needs. Sugar and water have none. Without help, the yeast runs out of food, stops early, and makes a smell like rotten eggs or burnt rubber.

A good plan for a 5 gallon batch is:

  • Yeast nutrient: a blend made for seltzer or wine, added in two or three doses over the first few days. Follow the dose on the pack.
  • A healthy amount of yeast: a full packet of a clean, strong strain. Champagne yeast such as EC-1118 and clean ale yeast both work.
  • A pH check: sugar water becomes very acidic as it ferments, which can stall the yeast. A pinch of baking soda or a little potassium bicarbonate keeps the pH above 3.5.

How do you make hard seltzer step by step?

  1. Sanitise the fermenter, lid, airlock and spoon.
  2. Dissolve the sugar in a gallon of hot water, and boil it for 10 minutes if you want to be sure it is clean.
  3. Top up with cool water to your full batch size.
  4. Take a gravity reading and compare it with the chart.
  5. Add the yeast and the first dose of nutrient when the liquid is below 75°F (24°C).
  6. Ferment for 1 to 2 weeks at 65 to 72°F, adding the rest of the nutrient on days 2 and 4.
  7. Wait until the gravity is steady below 1.000 for three days.
  8. Let it clear in a cool place for a week, or use a clearing agent.
  9. Add flavour, then carbonate.

How do you flavour and carbonate it?

Add flavour after fermentation, not before. Yeast would eat the sugar in fruit juice and change the taste. Natural fruit extracts and flavour drops are the easiest, because they add taste with no sugar. A typical dose is 1 to 2 ounces of extract for 5 gallons, but add a little, taste, and repeat.

A small amount of citric acid, about 1 teaspoon per 5 gallons, gives the bright, crisp edge that commercial seltzers have.

Seltzer is fizzier than beer. Aim for 2.8 to 3.0 volumes of carbon dioxide.

MethodHowGood for
KegChill and add gas from a cylinderFastest, lets you add sweet flavours safely
Bottle conditioningAdd priming sugar and sealNo extra equipment, dry seltzer only

The keg carbonation calculator gives the pressure for your temperature, and the priming sugar calculator gives the sugar for bottles. Use strong bottles at this fizz level. The safety advice in our guide to priming sugar for cider applies here too.

What is the shortcut method with vodka?

You can skip fermentation completely. Mix a neutral spirit with plain sparkling water and a flavour. Many canned seltzers on the shelf are made this way. The ABV is easy to set, because you are only diluting.

Spirit needed = glass size × target ABV ÷ spirit ABV

Target ABV80 proof vodka in a 12 oz drinkSparkling water
4%1.2 oz10.8 oz
5%1.5 oz (one shot)10.5 oz
6%1.8 oz10.2 oz
8%2.4 oz9.6 oz

One standard shot in a 12 ounce glass of seltzer is a 5% drink. For bigger batches or other spirits, the alcohol dilution calculator and the Pearson’s Square calculator give the exact amounts.

How many calories and carbs are in homemade hard seltzer?

When all the sugar ferments, the only calories left are from the alcohol. Alcohol has 7 calories per gram.

ABVCalories per 12 ozCarbs
4%780 to 1 g
5%980 to 1 g
6%1180 to 1 g
8%1570 to 1 g

If you sweeten the seltzer with sugar or juice after fermentation, add 4 calories for every gram of sugar. A sugar-free sweetener keeps the numbers in the table. Background on the drink itself is in Wikipedia’s hard seltzer article.

What goes wrong, and how do you fix it?

ProblemLikely causeFix
Fermentation stops earlyNot enough nutrient, or pH too lowAdd nutrient, raise pH slightly, warm it up
Rotten egg smellStressed, hungry yeastAdd nutrient early next time; the smell often fades with time
Cloudy seltzerYeast still floatingChill for a week or use a clearing agent
Tastes like cider or wineFermented too warmKeep it under 72°F
Weaker than plannedToo much water or sugar not fully dissolvedMeasure gravity before adding yeast

Frequently Asked Questions

What is the ABV of hard seltzer?

Most hard seltzer is 4 to 6 percent ABV, and 5 percent is the most common. Some stronger versions reach 8 percent.

How much sugar do I need for 5 gallons of hard seltzer?

Use about 3.5 pounds (1.6 kg) of white sugar for 5 gallons of 5 percent hard seltzer. Use 4.3 pounds for 6 percent.

Is hard seltzer stronger than beer?

Usually not. A standard hard seltzer and a regular beer are both about 5 percent ABV, so a 12 ounce can of either is one standard drink.

Can I make hard seltzer with vodka?

Yes. Mix one 1.5 ounce shot of 80 proof vodka with 10.5 ounces of sparkling water for a 12 ounce drink at 5 percent ABV.

How long does hard seltzer take to ferment?

With enough nutrient, a sugar and water seltzer ferments in 1 to 2 weeks. Allow another week for it to clear.

Why does my hard seltzer smell like sulfur?

Sugar water has no natural nutrients, so the yeast becomes stressed and makes sulfur smells. Adding yeast nutrient in stages prevents it.

Scroll to Top