Boil-Off Calculator

Work out your kettle’s boil-off rate from a single brew. Enter your pre-boil and post-boil volumes and the boil time, and the boil-off calculator shows how much wort you lost, the rate per hour, and the percentage that evaporated.

How the boil-off calculator works

During the boil, water leaves your kettle as steam while the sugars stay behind. The boil-off calculator measures how fast that happens on your own system. It takes the difference between your pre-boil and post-boil volumes, then divides by the boil time to give a rate per hour.

The three numbers it returns are simple but powerful. The total boiled off is just pre-boil minus post-boil. The boil-off rate is that total spread over an hour. The boil-off percentage is the share of your starting volume that evaporated. Once you know your rate, you can plan every future brew without guessing.

Boil-off rate = (pre-boil volume minus post-boil volume) divided by boil time in hours. For example, 7 gallons down to 5.5 gallons over a 60-minute boil is a 1.5 gal/hr rate.

Why your boil-off rate matters

Your boil-off rate is one of the most useful numbers in all-grain brewing. It decides how much water to start with so you finish the boil at your target batch size. Start with too little and you end up short and too strong; start with too much and your beer is watery and weak.

It also changes your gravity. As water leaves, the sugars concentrate, so your gravity climbs during the boil. Knowing your rate lets you predict your final volume and your original gravity before you even light the burner. It feeds straight into your brewhouse efficiency and your pre-boil gravity planning.

What is a typical boil-off rate?

Every system is different, but most homebrew kettles sit in a predictable range. Measure yours once and reuse it, because it stays fairly steady as long as your kettle and burner do not change.

SetupTypical boil-off rate
Small electric, 5 gallon batch0.5 to 1.0 gal/hr (2 to 4 L/hr)
Gas burner, 5 gallon batch1.0 to 1.5 gal/hr (4 to 6 L/hr)
Wide kettle, strong boil1.5 gal/hr or more
As a percentageOften 8 to 15% of the pre-boil volume per hour

If your rate is far outside these ranges, check that you measured at boiling temperature both times, since hot wort takes up more space than cool wort.

What affects your boil-off rate?

Boil-off is driven mostly by how much surface area is exposed to the air, not by how much heat you pour in. The main factors are below.

FactorEffect on boil-off
Kettle widthWider kettle, more surface, faster boil-off
Boil vigourA harder rolling boil evaporates more
Lid positionA partly covered kettle slows evaporation
Humidity and air flowDry, breezy air speeds evaporation
AltitudeHigher altitude lowers the boiling point and can raise the rate

Because kettle width matters most, the same burner can give very different rates in a narrow pot versus a wide one. This is why you should measure your own system rather than copy someone else’s number.

How to measure your boil-off rate accurately

The most reliable way is to measure during a real brew, or a water-only test run that copies your brew day.

  • Measure hot. Take your pre-boil volume once the wort reaches a boil, and your post-boil volume right at flameout, both at boiling temperature.
  • Keep the boil consistent. Use the same burner setting and lid position you always use.
  • Use a marked dip stick. A notched stick or a sight glass is more accurate than guessing.
  • Record the time. Note the exact minutes between your two readings.
  • Repeat once or twice. Averaging two brews smooths out small errors.

Enter those numbers above and you have a rate you can trust. From there, plan your water with the strike water calculator and the mash water calculator.

Using your rate to plan the next brew

Once you know your rate, the planning is easy. Decide your target post-boil volume, then work backwards.

Pre-boil volume needed = target post-boil volume plus (boil-off rate times boil time in hours). Say you want 5.5 gallons after a 90-minute boil and your rate is 1.2 gal/hr. You need 5.5 plus (1.2 times 1.5), which is 5.5 plus 1.8, or 7.3 gallons before the boil, plus a little extra for trub and hop losses.

Because the sugars concentrate as volume drops, your gravity rises too. Check the strength you will reach with the potential alcohol calculator and confirm the finished beer with the ABV calculator. For a deeper dive into boiling, the Brew Your Own magazine archive and the American Homebrewers Association are reliable resources.

Tips to control boil-off

  • Dial in a gentle rolling boil. A violent boil wastes energy and can strip flavour without improving the beer.
  • Use a lid, partly on. Cracking the lid slows boil-off if your rate is too high, though never fully cover a boil during the first stages.
  • Measure every season. Winter and summer air can shift your rate, especially if you brew outdoors.
  • Keep notes. A simple log of pre and post volumes turns guesswork into a reliable recipe.

Boil-off and high-gravity brewing

Boil-off becomes even more important when you brew big beers. Strong styles like imperial stouts, barleywines, and double IPAs start with a lot of sugar, which means a high pre-boil volume and often a longer boil. A long, hard boil can remove two gallons or more, so a small error in your rate turns into a large miss on volume and gravity.

Some brewers use this on purpose. By boiling longer, you concentrate the wort and push the gravity higher without adding more grain. This is a cheap way to add strength, but it costs time and energy, and it can darken the beer and deepen caramel flavours. Knowing your exact boil-off rate lets you choose the boil length that hits your target gravity on purpose rather than by luck.

If you still fall short, topping up with dry malt extract is a reliable fix, and if you overshoot, a measured water addition brings the gravity back down. Either way, start from an accurate rate.

Common boil-off mistakes to avoid

A few simple errors throw off most boil-off numbers. Watch for these and your planning will stay accurate brew after brew.

  • Mixing hot and cold readings. This is the biggest error. Always measure both volumes at the same temperature, ideally at a boil.
  • Copying someone else’s rate. A number from a forum or another kettle rarely matches yours. Measure your own system.
  • Ignoring trub and hop loss. Boil-off is only part of your total loss. Leave extra for the wort that stays behind with the hops and break material.
  • Changing your boil without remeasuring. A new kettle, a stronger burner, or an indoor-to-outdoor move all change the rate.
  • Boiling with the lid fully on. This traps compounds you usually want to drive off, and it makes your rate unpredictable.

Avoid these and the number from this boil-off calculator becomes a dependable part of your recipe planning, working hand in hand with the brewhouse efficiency calculator.

Frequently Asked Questions

What is a good boil-off rate for homebrewing?

Most systems lose 0.5 to 1.5 gallons (2 to 6 litres) per hour, or roughly 8 to 15 percent of the pre-boil volume. Wider kettles and stronger boils sit at the higher end.

How do I calculate my boil-off rate?

Subtract your post-boil volume from your pre-boil volume to get the total boiled off, then divide by the boil time in hours. For example, losing 1.5 gallons over a 60-minute boil is 1.5 gallons per hour.

Should I measure volume hot or cold?

Measure both volumes at boiling temperature. Hot wort takes up more space than cool wort, so mixing hot and cold readings gives a wrong rate.

What affects how fast wort boils off?

Mainly the surface area of your kettle, so wider kettles evaporate faster. Boil vigour, lid position, humidity, air flow, and altitude also matter. Burner power matters less than people think.

How do I use my boil-off rate to plan a brew?

Pre-boil volume equals your target post-boil volume plus the boil-off rate times the boil time in hours, with a little extra for trub and hop losses.

Does boiling off water change my gravity?

Yes. Water leaves as steam but sugar stays, so the wort concentrates and the gravity rises as the volume falls during the boil.

Scroll to Top