Pre-Boil Gravity Calculator
Use this pre-boil gravity calculator to predict your original gravity before the boil even ends. Enter your measured pre-boil gravity and volume plus your target post-boil volume, and it shows the expected OG so you can check your mash and adjust on the fly.
How the pre-boil gravity calculator works
When you collect your wort before the boil, it is thinner and larger in volume than the finished wort will be. As the boil drives off water, the sugars concentrate and the gravity climbs. This pre-boil gravity calculator uses that relationship to predict your original gravity, the OG, before the boil is even over.
The key idea is that boiling removes water but not sugar, so the total sugar stays the same. In brewing maths, the gravity points multiplied by the volume are conserved. The calculator takes your pre-boil gravity and volume, then scales the gravity up by the ratio of pre-boil to post-boil volume.
Expected OG points = pre-boil points x (pre-boil volume / post-boil volume). Gravity points are (specific gravity minus 1) times 1000, so 1.040 is 40 points. Concentrating 7 gallons at 40 points down to 5.5 gallons gives about 51 points, or 1.051.
Why pre-boil gravity is the most useful brew-day check
Measuring your pre-boil gravity is the single best quality check in all-grain brewing. It is the first moment you learn whether your mash worked, long before the beer is finished. If the number is on target, your grain crush, mash temperature, and sparge all did their job. If it is low, you have time to fix it.
It directly reflects your mash efficiency, which is how much sugar you pulled out of the grain. A low pre-boil gravity means low efficiency, and knowing that early lets you boil longer or add extract to still hit your recipe. Waiting until the end of the boil to find out leaves you with no easy fix. This check works hand in hand with the brewhouse efficiency calculator.
What pre-boil gravity should you expect?
Your pre-boil gravity is always lower than your target OG, because the wort has not been concentrated yet. How much lower depends on how much you boil off. These are rough guides for a 60 to 90 minute boil.
| Target OG | Typical pre-boil gravity |
|---|---|
| 1.040 | About 1.030 to 1.034 |
| 1.050 | About 1.038 to 1.043 |
| 1.060 | About 1.046 to 1.052 |
| 1.070 | About 1.054 to 1.060 |
The exact gap depends on your boil-off. Measure your evaporation first with the boil-off calculator, then you can set a precise pre-boil gravity target for every recipe.
How to measure pre-boil gravity
Take the reading once you have collected all your wort in the kettle, before you turn on the heat or right as it starts to warm.
- Stir first. Mix the wort well so the sugars are even, or your reading will be off.
- Correct for temperature. Hydrometers are calibrated to a set temperature, so adjust a hot sample with the hydrometer temperature correction tool.
- Or use a refractometer. A few drops are enough, and no cooling is needed. Convert the reading with the Brix to specific gravity converter.
- Note the volume. Measure your pre-boil volume at the same time with a marked dip stick.
Enter both into the calculator and compare the expected OG to your recipe. That comparison is where the real value is.
How to fix a pre-boil gravity that is off
The whole point of measuring early is that you still have time to react. Here is what to do in each case.
| Situation | What it means | Fix |
|---|---|---|
| Expected OG below target | Low mash efficiency | Boil longer to concentrate, or add dry or liquid malt extract |
| Expected OG above target | High efficiency or low volume | Add water to dilute to your target |
| Expected OG on target | Everything worked | Boil as planned and relax |
Boiling longer is the cheapest fix, but it uses more time and energy and can darken the beer. Adding extract is faster and more predictable. Either way, confirm the strength you will reach with the potential alcohol calculator.
Understanding gravity points
Gravity points make this maths much easier. Instead of working with numbers like 1.048, brewers drop the 1 and the decimal and talk in points, so 1.048 becomes 48 points. Points are just the specific gravity minus 1, multiplied by 1000.
The useful rule is that points times volume stays constant through the boil. If you have 7 gallons at 35 points, that is 245 point-gallons. Boil down to 5 gallons and you still have 245 point-gallons, so the gravity is now 49 points, or 1.049. This simple conservation is the engine behind both the pre-boil gravity and the boil-off calculators. For more on brew-day gravity, the Brew Your Own archive and the American Homebrewers Association are excellent resources, and you can confirm your finished beer with the ABV calculator.
A brew-day example
Imagine you are brewing a pale ale with a recipe target of 1.052. You collect 7 gallons of wort and plan to finish with 5.5 gallons after the boil. You stir the kettle, pull a sample, correct it for temperature, and read 1.040.
Enter 1.040 as the pre-boil gravity, 7 as the pre-boil volume, and 5.5 as the post-boil volume. The calculator concentrates 40 points over that volume ratio and predicts an OG of about 1.051. That is almost exactly your 1.052 target, so your mash hit its mark and you can boil as planned. If the reading had been 1.035 instead, the predicted OG would land near 1.045, a clear sign of low efficiency, and you would boil a little longer or stir in some dry malt extract to recover.
This two-minute check turns brew day from hoping for the best into knowing where you stand. It is the difference between finding a problem when you can still fix it and finding it when the beer is already in the fermenter.
Pre-boil gravity and mash efficiency
Pre-boil gravity and mash efficiency are two sides of the same coin. Efficiency is the share of the available sugar you actually extracted from the grain, and your pre-boil gravity is the direct evidence of it. A higher pre-boil gravity for the same grain bill means higher efficiency.
Tracking this over several brews is how you learn your system. If your pre-boil gravity is consistently low, you can improve it by crushing your grain finer, holding a steady mash temperature, sparging more slowly, or giving the mash more time. Small changes often add several points. Once your efficiency is steady and known, your recipes become repeatable, and you can design a beer and trust that it will come out at the gravity you planned.
Keep a simple log of your target OG, your measured pre-boil gravity, and your volumes for each brew. Over time that record is worth more than any single calculator, because it captures exactly how your own kit behaves. Feed those numbers into the brewhouse efficiency calculator and the boil-off calculator to complete the picture.
Frequently Asked Questions
How do I calculate pre-boil gravity?
Gravity points times volume are conserved during the boil. Multiply your pre-boil gravity points by the ratio of pre-boil volume to post-boil volume to get your expected original gravity.
What is the difference between pre-boil and original gravity?
Pre-boil gravity is measured before the boil, when the wort is larger and thinner. Original gravity is after the boil, once water has evaporated and the sugars have concentrated, so OG is higher.
What should my pre-boil gravity be?
It is lower than your target OG by the amount you boil off. For a 1.050 OG you might aim for roughly 1.038 to 1.043 pre-boil, depending on your evaporation rate.
My pre-boil gravity is too low. What do I do?
A low reading means low mash efficiency. You can boil longer to concentrate the wort, or add dry or liquid malt extract to raise the gravity to your target.
My pre-boil gravity is too high. What do I do?
Add water to dilute the wort down to your target gravity. This happens when your efficiency is high or your collected volume is a little low.
Do I need to correct pre-boil gravity for temperature?
Yes, if you use a hydrometer. Hydrometers read correctly only at their calibration temperature, so adjust a hot sample, or use a refractometer which needs just a few drops.